Loading...
HomeMy WebLinkAboutBetco Dust Mop Treatment (Aerosol)Dust Mop Treatment Not available. Aerosol. GHS product identifier Other means of identification Product type Section 1. Identification : : : Relevant identified uses of the substance or mixture and uses advised against Dust Mop Treatment Identified uses Not applicable. Uses advised against Product code :035 Dust Mop Treatment SAFETY DATA SHEET Chemtrec (800) 424-9300 24 hourEmergency telephone number : Supplier's details :Betco Corporation 400 Van Camp Road Bowling Green, Ohio 43402 www.betco.com 888-462-3826 Section 2. Hazards identification FLAMMABLE AEROSOLS - Category 1 GASES UNDER PRESSURE - Liquefied gas SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) - Category 3 ASPIRATION HAZARD - Category 1 Classification of the substance or mixture : Signal word :Danger Hazard statements :Extremely flammable aerosol. Contains gas under pressure; may explode if heated. May be fatal if swallowed and enters airways. Causes skin irritation. Causes serious eye irritation. May cause drowsiness or dizziness. Hazard pictograms : Precautionary statements Prevention :Wear protective gloves. Wear eye or face protection: Recommended: safety glasses with side-shields. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing dust or mist. Wash thoroughly after handling. Pressurized container: Do not pierce or burn, even after use. GHS label elements OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200). Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 1/14 Dust Mop Treatment Section 2. Hazards identification Response :IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell. IF SWALLOWED: Immediately call a POISON CENTER or doctor. Do NOT induce vomiting. Take off contaminated clothing and wash it before reuse. IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice or attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or attention. Storage :Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Disposal :Dispose of contents and container in accordance with all local, regional, national and international regulations. Hazards not otherwise classified :None known. Section 3. Composition/information on ingredients Ingredient name CAS number% There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section. Other means of identification :Not available. Substance/mixture : Occupational exposure limits, if available, are listed in Section 8. Mixture Any concentration shown as a range is to protect confidentiality or is due to batch variation. propane ≤10 74-98-6 Distillates (petroleum), hydro- treated light ≤5 64742-47-8 White mineral oil (petroleum)≤5 8042-47-5 sodium nitrite ≤3 7632-00-0 (R)-p-mentha-1,8-diene ≤3 5989-27-5 Tall oil diethanolamide ≤3 68155-20-4 Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If necessary, call a poison center or physician. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. Section 4. First aid measures Eye contact Skin contact Inhalation : : : Description of necessary first aid measures Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 2/14 Dust Mop Treatment Section 4. First aid measures Get medical attention immediately. Call a poison center or physician. Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Ingestion : Protection of first-aiders :No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Notes to physician :In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. Specific treatments :No specific treatment. Most important symptoms/effects, acute and delayed Inhalation :Can cause central nervous system (CNS) depression. May cause drowsiness or dizziness. Can cause central nervous system (CNS) depression. May be fatal if swallowed and enters airways. :Ingestion Skin contact :Causes skin irritation. Causes serious eye irritation.:Eye contact Over-exposure signs/symptoms Skin contact Ingestion Inhalation Adverse symptoms may include the following: respiratory tract irritation coughing nausea or vomiting headache drowsiness/fatigue dizziness/vertigo unconsciousness Adverse symptoms may include the following: nausea or vomiting Adverse symptoms may include the following: irritation redness : : : Eye contact :Adverse symptoms may include the following: pain or irritation watering redness Potential acute health effects See toxicological information (Section 11) Indication of immediate medical attention and special treatment needed, if necessary Section 5. Fire-fighting measures Use an extinguishing agent suitable for the surrounding fire. Extinguishing media None known. Suitable extinguishing media : Unsuitable extinguishing media : Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 3/14 Dust Mop Treatment Section 5. Fire-fighting measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool. Hazardous thermal decomposition products Specific hazards arising from the chemical Decomposition products may include the following materials: carbon dioxide carbon monoxide nitrogen oxides metal oxide/oxides Extremely flammable aerosol. Runoff to sewer may create fire or explosion hazard. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. Gas may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back, causing fire or explosion. Bursting aerosol containers may be propelled from a fire at high speed. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Special protective equipment for fire-fighters : : : Special protective actions for fire-fighters : Section 6. Accidental release measures Environmental precautions Personal precautions, protective equipment and emergency procedures Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. : :No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. In the case of aerosols being ruptured, care should be taken due to the rapid escape of the pressurized contents and propellant. If a large number of containers are ruptured, treat as a bulk material spillage according to the instructions in the clean-up section. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Small spill : Methods and materials for containment and cleaning up For non-emergency personnel For emergency responders :If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 4/14 Dust Mop Treatment Section 7. Handling and storage Advice on general occupational hygiene Conditions for safe storage, including any incompatibilities Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Store in accordance with local regulations. Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Protect from sunlight. Store locked up. Eliminate all ignition sources. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use. : : Protective measures Put on appropriate personal protective equipment (see Section 8). Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50°C. Do not pierce or burn, even after use. Do not swallow. Avoid contact with eyes, skin and clothing. Avoid breathing gas. Avoid breathing vapor or mist. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use only non-sparking tools. Empty containers retain product residue and can be hazardous. : Precautions for safe handling propane OSHA PEL 1989 (United States, 3/1989). TWA: 1000 ppm 8 hours. TWA: 1800 mg/m³ 8 hours. NIOSH REL (United States, 10/2020). TWA: 1000 ppm 10 hours. TWA: 1800 mg/m³ 10 hours. OSHA PEL (United States, 5/2018). TWA: 1000 ppm 8 hours. TWA: 1800 mg/m³ 8 hours. ACGIH TLV (United States, 1/2022). Oxygen Depletion [Asphyxiant]. Explosive potential. CAL OSHA PEL (United States, 5/2018). TWA: 1800 mg/m³ 8 hours. TWA: 1000 ppm 8 hours. Distillates (petroleum), hydro- treated light ACGIH TLV (United States, 1/2022). [Kerosene as total hydrocarbon vapor] Absorbed through skin. TWA: 200 mg/m³, (as total hydrocarbon vapor) 8 hours. White mineral oil (petroleum)OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m³ 8 hours. ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m³ 10 hours. Form: Mist STEL: 10 mg/m³ 15 minutes. Form: Mist sodium nitrite None. Section 8. Exposure controls/personal protection Ingredient name Exposure limits Control parameters Occupational exposure limits Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 5/14 Dust Mop Treatment Section 8. Exposure controls/personal protection (R)-p-mentha-1,8-diene OARS WEEL (United States, 4/2022). TWA: 30 ppm 8 hours. Tall oil diethanolamide None. Hand protection Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles. Recommended: safety glasses with side-shields Eye/face protection Respiratory protection : : : Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. When there is a risk of ignition from static electricity, wear anti- static protective clothing. For the greatest protection from static discharges, clothing should include anti-static overalls, boots and gloves. Recommended: Chemical resistant gloves : Environmental exposure controls :Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Appropriate engineering controls :Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Hygiene measures : Individual protection measures Skin protection Other skin protection :Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Biological exposure indices No exposure indices known. Section 9. Physical and chemical properties and safety characteristics Physical state Liquid. [Aerosol. Compressed gas. Emulsion.] White.Color : : Appearance The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated. Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 6/14 Dust Mop Treatment Section 9. Physical and chemical properties and safety characteristics Melting point/freezing point Vapor pressure Relative density Relative vapor density Not available. 0.676 Not available. Fruity.Odor pH Auto-ignition temperature Flash point Not available. Closed cup: -104.4°C (-155.9°F) [Product does not sustain combustion.] Not applicable. Not applicable. Viscosity Not available. Not available.Odor threshold Partition coefficient: n- octanol/water : : : : : : : : : : : Boiling point, initial boiling point, and boiling range :Not available. Flammability :Not available. Lower and upper explosion limit/flammability limit :Not available. Decomposition temperature :Not available. Type of aerosol :Spray Heat of combustion :4.695 kJ/g Aerosol product Solubility in water :Not available. Particle characteristics Median particle size :Not applicable. Ingredient name Vapor Pressure at 20˚C Vapor pressure at 50˚C mm Hg kPa Method mm Hg kPa Method propane 6300.51 840 butane 1602.88 213.7 water 17.5 2.3 (R)-p-mentha-1,8-diene 1.5 0.2 Distillates (petroleum), hydro-treated light 0.23 to 0.45 0.031 to 0.06 White mineral oil (petroleum)0.08 0.011 OECD 104 2,2'-iminodiethanol <0.0075 <0.001 Section 10. Stability and reactivity Conditions to avoid Avoid all possible sources of ignition (spark or flame). The product is stable.Chemical stability No specific data. : : Incompatible materials : Possibility of hazardous reactions :Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity :No specific test data related to reactivity available for this product or its ingredients. Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 7/14 Dust Mop Treatment Section 10. Stability and reactivity Hazardous decomposition products Under normal conditions of storage and use, hazardous decomposition products should not be produced. : Section 11. Toxicological information Acute toxicity White mineral oil (petroleum)LD50 Oral Rat >5000 mg/kg - (R)-p-mentha-1,8-diene LD50 Dermal Rabbit >5000 mg/kg - LD50 Oral Rat 4400 mg/kg - Product/ingredient name Result Species Dose Exposure Carcinogenicity Not available. Mutagenicity Not available. Teratogenicity Not available. Reproductive toxicity Not available. Irritation/Corrosion sodium nitrite Eyes - Mild irritant Rabbit -24 hours 500 mg - (R)-p-mentha-1,8-diene Skin - Mild irritant Rabbit -24 hours 10 % - Product/ingredient name Result Score Exposure Observation Sensitization Not available. Species Information on the likely routes of exposure Causes serious eye irritation.:Eye contact Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Dust Mop Treatment Category 3 -Narcotic effects propane Category 3 -Respiratory tract irritation Product/ingredient name Category Not available. Aspiration hazard Product/ingredient name Result Dust Mop Treatment ASPIRATION HAZARD - Category 1 Distillates (petroleum), hydro- treated light ASPIRATION HAZARD - Category 1 White mineral oil (petroleum)ASPIRATION HAZARD - Category 1 Route of exposure Target organs Information on toxicological effects :Routes of entry anticipated: Dermal, Inhalation, Eyes. Potential acute health effects Classification sodium nitrite -2A - (R)-p-mentha-1,8-diene -3 - Product/ingredient name NTPIARCOSHA Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 8/14 Dust Mop Treatment Section 11. Toxicological information Not available. Inhalation :Can cause central nervous system (CNS) depression. May cause drowsiness or dizziness. Can cause central nervous system (CNS) depression. May be fatal if swallowed and enters airways. :Ingestion Skin contact :Causes skin irritation. No known significant effects or critical hazards.General : No known significant effects or critical hazards.Carcinogenicity : No known significant effects or critical hazards.Mutagenicity : No known significant effects or critical hazards.Reproductive toxicity : Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Inhalation Adverse symptoms may include the following: respiratory tract irritation coughing nausea or vomiting headache drowsiness/fatigue dizziness/vertigo unconsciousness Adverse symptoms may include the following: nausea or vomiting Adverse symptoms may include the following: irritation redness : : : Eye contact :Adverse symptoms may include the following: pain or irritation watering redness Potential chronic health effects Delayed and immediate effects and also chronic effects from short and long term exposure Numerical measures of toxicity Acute toxicity estimates Potential immediate effects :Not available. Short term exposure Potential delayed effects :Not available. Potential immediate effects :Not available. Long term exposure Potential delayed effects :Not available. Product/ingredient name sodium nitrite 100 N/A N/A N/A N/A (R)-p-mentha-1,8-diene 4400 N/A N/A N/A N/A Oral (mg/ kg) Dermal (mg/kg) Inhalation (gases) (ppm) Inhalation (vapors) (mg/l) Inhalation (dusts and mists) (mg/ l) Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 9/14 Dust Mop Treatment Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects :No known significant effects or critical hazards. Product/ingredient name propane 1.09 -Low White mineral oil (petroleum)>6 -High sodium nitrite -3.7 -Low (R)-p-mentha-1,8-diene 4.38 -High Toxicity Distillates (petroleum), hydro- treated light Acute LC50 2200 µg/l Fresh water Fish - Lepomis macrochirus 4 days sodium nitrite Acute EC50 159000 µg/l Marine water Algae - Tetraselmis chuii 72 hours Acute EC50 1600000 µg/l Marine water Algae - Tetraselmis chuii 96 hours Acute LC50 1100 µg/l Fresh water Crustaceans - Cherax quadricarinatus 48 hours Acute LC50 18.75 mg/l Fresh water Daphnia - Daphnia similoides 48 hours Acute LC50 0.16 µg/l Fresh water Fish - Ictalurus punctatus - Fingerling 96 hours Chronic NOEC 0.1 mg/l Daphnia - Daphnia obtusa - Neonate 21 days Chronic NOEC 0.01 mg/l Fresh water Fish - Oncorhynchus mykiss 28 days (R)-p-mentha-1,8-diene Acute EC50 421 µg/l Fresh water Daphnia - Daphnia magna 48 hours Acute EC50 688 µg/l Fresh water Fish - Pimephales promelas - Juvenile (Fledgling, Hatchling, Weanling) 96 hours Product/ingredient name SpeciesResult Exposure Persistence and degradability Soil/water partition coefficient (KOC) :Not available. Mobility in soil Not available. Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Empty containers or liners may retain some product residues. Do not puncture or incinerate container. :Disposal methods Section 14. Transport information Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 10/14 Dust Mop Treatment Section 14. Transport information Aerosols 2.1 - Aerosols 2.1 - Aerosols UN1950 2.1 - UN1950 UN1950 Reportable quantity 10000 lbs / 4540 kg [1774.2 gal / 6716 L]. Package sizes shipped in quantities less than the product reportable quantity are not subject to the RQ (reportable quantity) transportation requirements. Limited quantity Yes. Limited quantity Yes.- Limited quantity Yes.- DOT Classification UN number UN proper shipping name Transport hazard class(es) Packing group Additional information Environmental hazards Special precautions for user No.No.No. Transport within user’s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. : UN1950 Aerosols 2.1 - No. Product classified as per the following sections of the Transportation of Dangerous Goods Regulations: 2.13-2.17 (Class 2). Explosive Limit and Limited Quantity Index 1 UN1950 Aerosols 2.1 - No. DOT Classification TDG Classification IMDG IATA : : : : TDG Classification Mexico Classification IMDG IATA Transport in bulk according to IMO instruments :Not available. Section 15. Regulatory information U.S. Federal regulations Clean Water Act (CWA) 311: sodium nitrite Clean Air Act (CAA) 112 regulated flammable substances: propane; butane : Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) :Listed Clean Air Act Section 602 Class I Substances :Not listed Clean Air Act Section 602 Class II Substances :Not listed DEA List I Chemicals (Precursor Chemicals) :Not listed DEA List II Chemicals (Essential Chemicals) :Not listed TSCA 5(a)2 final significant new use rules: sodium nitrite TSCA 8(a) CDR Exempt/Partial exemption: Not determined TSCA 12(b) one-time export: sodium nitrite SARA 302/304 Composition/information on ingredients Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 11/14 Dust Mop Treatment Section 15. Regulatory information The following components are listed: PROPANE; BUTANE; OIL MIST, MINERAL; SODIUM NITRITE WARNING: This product can expose you to Diethanolamine, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov. Massachusetts : SARA 313 Product name CAS number % SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include copying and redistribution of the notice attached to copies of the SDS subsequently redistributed. Diethanolamine -- Ingredient name No significant risk level Maximum acceptable dosage level sodium nitrite 7632-00-0 ≤3 sodium nitrite 7632-00-0 ≤3 Form R - Reporting requirements Supplier notification California Prop. 65 New York :The following components are listed: Sodium nitrite New Jersey :The following components are listed: PROPANE; BUTANE; SODIUM NITRITE Pennsylvania :The following components are listed: PROPANE; BUTANE; NITROUS ACID, SODIUM SALT State regulations SARA 304 RQ :Not applicable. No products were found. International regulations Chemical Weapon Convention List Schedules I, II & III Chemicals Not listed. SARA 311/312 Classification :FLAMMABLE AEROSOLS - Category 1 GASES UNDER PRESSURE - Liquefied gas SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) - Category 3 ASPIRATION HAZARD - Category 1 propane ≤10 FLAMMABLE GASES - Category 1 GASES UNDER PRESSURE - Liquefied gas SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract irritation) - Category 3 butane ≤10 FLAMMABLE GASES - Category 1 GASES UNDER PRESSURE - Compressed gas Distillates (petroleum), hydro- treated light ≤5 FLAMMABLE LIQUIDS - Category 3 ASPIRATION HAZARD - Category 1 White mineral oil (petroleum)≤5 ASPIRATION HAZARD - Category 1 sodium nitrite ≤3 OXIDIZING SOLIDS - Category 3 ACUTE TOXICITY (oral) - Category 3 EYE IRRITATION - Category 2A (R)-p-mentha-1,8-diene ≤3 FLAMMABLE LIQUIDS - Category 3 SKIN IRRITATION - Category 2 SKIN SENSITIZATION - Category 1 Tall oil diethanolamide ≤3 SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A Name %Classification Composition/information on ingredients Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 12/14 Dust Mop Treatment Section 15. Regulatory information Montreal Protocol Not listed. Stockholm Convention on Persistent Organic Pollutants Not listed. Rotterdam Convention on Prior Informed Consent (PIC) UNECE Aarhus Protocol on POPs and Heavy Metals Not listed. Inventory list Australia :Not determined. Canada :Not determined. China :Not determined. Japan :Japan inventory (CSCL): Not determined. Japan inventory (ISHL): Not determined. Republic of Korea :Not determined. New Zealand :Not determined. Philippines :Not determined. Taiwan :Not determined. Turkey :Not determined. United States :Not determined. Thailand :Not determined. Viet Nam :Not determined. Not listed. Eurasian Economic Union :Russian Federation inventory: Not determined. Section 16. Other information Hazardous Material Information System (U.S.A.) 3 3 3 0 4 2 / National Fire Protection Association (U.S.A.) Health Special hazards Instability Flammability Health Flammability Physical hazards Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc. The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual. Procedure used to derive the classification Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 13/14 Dust Mop Treatment Section 16. Other information 4/29/2024 History Date of printing Date of issue/Date of revision Version Notice to reader Date of previous issue : : : : Indicates information that has changed from previously issued version. References :Not available. Key to abbreviations :ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group UN = United Nations 4/29/2024 No previous validation 1 Classification Justification FLAMMABLE AEROSOLS - Category 1 Expert judgment GASES UNDER PRESSURE - Liquefied gas Expert judgment SKIN IRRITATION - Category 2 Expert judgment EYE IRRITATION - Category 2A Expert judgment SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) - Category 3 Expert judgment ASPIRATION HAZARD - Category 1 Expert judgment To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Date of issue/Date of revision :4/29/2024 Date of previous issue :No previous validation Version :1 14/14